How to Set Okuma RS-232 Parameters - 5000M-G, 5020M, 700M, 7000M

How to Set Okuma RS-232 Parameters - 5000M-G, 5020M, 700M, 7000M

Controls

  1. OSP5000M-G
  2. OSP5020M
  3. OSP700M
  4. OSP7000M
Notate or take a picture of any parameters before you change them

Change Okuma Parameters

  1. Ensure the NC PANEL key is set to "UNLOCK"
  2. Press PARAMETER button
  3. Press ITEM DOWN (F7) softkey until you get to "NC OPTIONAL PARAMETER (WORD)"
  4. Change the following parameters
    5. PAGE UP and PAGE DOWN keys to navigate between "NC OPTIONAL PARAMETER (WORD)" pages
    To change the parameter, highlight the value, press SET, type in new value, then press WRITE button
    1. #1 = 1 (Feed Holes)
    2. #6 = 4800 (Baud Rate)
    3. #34 = 30 (Busy Time)
    4. #45 = 0 (Punch Port)
    5. #57 = 1 (Read Port)
  5. Press ITEM DOWN (F7) softkey until you get to "NC OPTIONAL PARAMETER (BIT)"
  6. Change the following parameters
    7. PAGE UP and PAGE DOWN keys to navigate between "NC OPTIONAL PARAMETER (WORD)" pages
    To change the parameter, highlight the bit, press SET, type in new bit, then press WRITE button
    1. #1 = 00011011
    2. #8 = 10101011
  7. Reboot control

Alternative Parameters

The following set of parameters have been known to work. Try these if the above parameters do not work.
  1. Alternative 1
    1. NC OPTIONAL PARAMETER (BIT)
      1. #1 = 00000000
      2. #8 = 10101010
  2. Alternative 2
      1. NC OPTIONAL PARAMETER (BIT)
        1. #1 = 01011011
        2. #8 = 10100010
    1. Alternative 3
        1. NC OPTIONAL PARAMETER (BIT)
          1. #1 = 00001011
          2. #8 = 10101010

      PC Settings

      1. Baud Rate = 4800
      2. Data Bits = 7
      3. Parity = Even
      4. Stop Bits = 1
      5. Flow Control = Xon/Xoff

      Troubleshooting

      1. Parameter changes are not retained after reboot
        1. Wait about 5 minutes after changing the last parameter
        2. Power off NC
        3. Wait about 2 minutes
        4. Power on NC and verify changes stuck



        • Related Articles

        • How to Set Okuma RS-232 Parameters - 5000L-G, 5020, 5020L, 700L, 7000L

          Controls OSP5000L-G OSP5020 OSP5020L OSP700L OSP7000L Notate or take a picture of any parameters before you change them Change Okuma Parameters Ensure the NC PANEL key is set to "UNLOCK" Press PARAMETER button Press ITEM DOWN (F7) softkey until you ...

        • How to Set Okuma P Series Parameters

          Controls OSP-P100L, OSP-P100M OSP-P200L, OSP-P200M, OSP-P200S, OSP-P200LA, OSP-P200MA, OSP-P200SA OSP-P300L, OSP-P300M, OSP-P300S, OSP-P300LA, OSP-P300MA, OSP-P300SA Notate or take a picture of any parameters before you change them Set Tape Puncher ...

        • How to Set Fadal RS-232 Parameters

          Controls All Fadal Controls Notate or take a picture of any parameters before you change them Set Parameters Press MANUAL button until you see “ENTER NEXT COMMAND <” Type “SETP” and press ENTER button Press ENTER button to keep G-code style setting ...

        • How to Set Haas RS-232 Parameters

          Controls All Haas prior to 2016 Any Haas 2016 or later with an RS-232 interface Notate or take a picture of any parameters before you change them Set Parameters Standard Transfers (Default) Press SETNG GRAPH button Press Page Down button until you ...

        • How to Set Fanuc RS-232 Parameters - 16, 18, 21, 0i, 30i, 31i, 32i

          Controls Fanuc 16-M, 16-T, 16i-M, 16i-T, 16i-MB, 16i-TB, 160i-MB, 160i-TB, 160is-MB, 160is-TB Fanuc 18-M, 18-T, 18i-M, 18i-T, 18i-MB, 18i-TB, 180i-MB, 180i-TB, 180is-MB, 180is-TB Fanuc 21-M, 21-T, 21i-M, 21i-T, 21i-MB, 21i-TB, 210i-MB, 210i-TB, ...