Mazak Mazatrol SMART RS-232 Parameters

Mazak Mazatrol SMART RS-232 Parameters

Controls

  1. Mazatrol SMART
Notate or take a picture of any parameters before you change them

Set TAPE (EIA) Parameters

  1. Press far-left softkey
  2. Press DATA I/O
  3. Press DATA I/O PARAM.
  4. Set BAUDRATE to "19200" (2400, 4800, 9600 may also be used)
  5. Set DATA BIT to "8"
  6. Set PARITY to "NONE"
  7. Set STOP BIT to "2"
  8. Set HAND SHAKE to "DC CNT"
  9. Set WAIT TIME to "5000"
  10. Set FORMAT to "ISO"
  11. Set SAME WNo. to "ALARM"
  12. Set PORT to "COM2"
  13. Set the following TAP parameters:
    1. TAP1
      1
      TAP9
      76
      TAP17
      0
      TAP25
      00000000
      TAP2
      0
      TAP10
      13
      TAP18
      0
      TAP26
      00000100
      TAP3
      0
      TAP11
      109
      TAP19
      0
      TAP27
      00000111
      TAP4
      0
      TAP12
      122
      TAP20
      0
      TAP28
      00000000
      TAP5
      1
      TAP13
      91
      TAP21
      0
      TAP29
      0
      TAP6
      0
      TAP14
      70
      TAP22
      0
      TAP30
      0
      TAP7
      0
      TAP15
      26
      TAP23
      0
      TAP31
      0
      TAP8
      0
      TAP16
      74
      TAP24
      0
      TAP32
      0
  14. Press DATA I/O to close
Notes
While the Mazak control is set to 8 Data Bit, None Parity, & 2 Stop Bit, the computer or hardware sending the part program should be 7 Data Bit, Even Parity, & 2 Stop Bit

Troubleshooting

If the TAPE option is missing from DATA I/O, press far left softkey, press PARAM, press EIA/ISO [F], change F163 bit 6 to 1 (X1XXXXXX). To change, press BIT INPUT, then press BIT 6 to select it, it will change BIT 6 to 1. 

    • Related Articles

    • Mazak Mazatrol 640 RS-232 Parameters

      Controls Mazatrol 640T, 640M Mazatrol 640T, 640M Nexus PC-Fusion-CNC Notate or take a picture of any parameters before you change them Set TAPE (EIA) Parameters Press far-left softkey Press DATA I/O Press TAPE Press PARAM. Set BAUDRATE to "19200" ...

    • Operator Guide - Mazak SMART

      Overview This will explain how to output a program (punch) from the CNC control and input a program (read) into the CNC control. Controls Supported Mazatrol SMART How to Punch SMART controls also punch Mazatrol programs via this TAPE interface. Press ...

    • Yasnac i80 RS-232 Parameters

      Control Yasnac i80 Notate or take a picture of any parameters before you change them Change Yasnac Parameters Press PROG key Press far right UP/DOWN softkey to select top row of softkeys (indicated by outlines) Press IN/OUT softkey Press RS232C ...

    • Fanuc 0 RS-232 Parameters

      Controls Fanuc 0M, 0T Notate or take a picture of any parameters before you change them Change Fanuc Parameters Put control in MDI mode Press DGNOS PARAM button until you see "PARAMETER" page Press PARAM softkey On SETTING 1 page, change the ...

    • Siemens 802D RS-232 Parameters

      Controls Siemens 802D Notate or take a picture of any parameters before you change them Change Siemens 802D Parameters Press Menu Select button Press Services softkey Press Devices softkey Select Standard interface from top Press Copy to clipboard ...