Okuma OSP 5000M-G, 5020M, 700M, 7000M RS-232 Parameters

Okuma OSP 5000M-G, 5020M, 700M, 7000M RS-232 Parameters

Controls

  1. OSP5000M-G
  2. OSP5020M
  3. OSP700M
  4. OSP7000M
Notate or take a picture of any parameters before you change them

Change Okuma Parameters

  1. Ensure the NC PANEL key is set to "UNLOCK"
  2. Press PARAMETER button
  3. Press ITEM DOWN (F7) softkey until you get to "NC OPTIONAL PARAMETER (WORD)"
  4. Change the following parameters
    5. PAGE UP and PAGE DOWN keys to navigate between "NC OPTIONAL PARAMETER (WORD)" pages
    To change the parameter, highlight the value, press SET, type in new value, then press WRITE button
    1. #1 = 1 (Feed Holes)
    2. #6 = 4800 (Baud Rate)
    3. #34 = 30 (Busy Time)
    4. #45 = 0 (Punch Port)
    5. #57 = 1 (Read Port)
  5. Press ITEM DOWN (F7) softkey until you get to "NC OPTIONAL PARAMETER (BIT)"
  6. Change the following parameters
    7. PAGE UP and PAGE DOWN keys to navigate between "NC OPTIONAL PARAMETER (WORD)" pages
    To change the parameter, highlight the bit, press SET, type in new bit, then press WRITE button
    1. #1 = 00011011
    2. #8 = 10101011
  7. Reboot control

Alternative Parameters

The following set of parameters have been known to work. Try these if the above parameters do not work.
  1. Alternative 1
    1. NC OPTIONAL PARAMETER (BIT)
      1. #1 = 00000000
      2. #8 = 10101010
  2. Alternative 2
      1. NC OPTIONAL PARAMETER (BIT)
        1. #1 = 01011011
        2. #8 = 10100010
    1. Alternative 3
        1. NC OPTIONAL PARAMETER (BIT)
          1. #1 = 00001011
          2. #8 = 10101010

      PC Settings

      1. Baud Rate = 4800
      2. Data Bits = 7
      3. Parity = Even
      4. Stop Bits = 1
      5. Flow Control = Xon/Xoff

      Troubleshooting

      1. Parameter changes are not retained after reboot
        1. Wait about 5 minutes after changing the last parameter
        2. Power off NC
        3. Wait about 2 minutes
        4. Power on NC and verify changes stuck



        • Related Articles

        • Okuma OSP 5000L-G, 5020, 5020L, 700L, 7000L RS-232 Parameters

          Controls OSP5000L-G OSP5020 OSP5020L OSP700L OSP7000L Notate or take a picture of any parameters before you change them Change Okuma Parameters Ensure the NC PANEL key is set to "UNLOCK" Press PARAMETER button Press ITEM DOWN (F7) softkey until you ...

        • Okuma OSP P100, P200, P300 RS-232 Parameters

          Controls OSP-P100L, OSP-P100M OSP-P200L, OSP-P200M, OSP-P200S, OSP-P200LA, OSP-P200MA, OSP-P200SA OSP-P300L, OSP-P300M, OSP-P300S, OSP-P300LA, OSP-P300MA, OSP-P300SA Notate or take a picture of any parameters before you change them Set Tape Puncher ...

        • Siemens 802D RS-232 Parameters

          Controls Siemens 802D Notate or take a picture of any parameters before you change them Change Siemens 802D Parameters Press Menu Select button Press Services softkey Press Devices softkey Select Standard interface from top Press Copy to clipboard ...

        • Fadal CNC 88HS RS-232 Parameters

          Controls All Fadal Controls Notate or take a picture of any parameters before you change them Set Parameters Press MANUAL button until you see “ENTER NEXT COMMAND <” Type “SETP” and press ENTER button Press ENTER button to keep G-code style setting ...

        • Mazak Mazatrol 640 RS-232 Parameters

          Controls Mazatrol 640T, 640M Mazatrol 640T, 640M Nexus PC-Fusion-CNC Notate or take a picture of any parameters before you change them Set EIA (TAPE) Parameters Press far-left softkey Press DATA I/O Press TAPE Press PARAM. Set BAUDRATE to "19200" ...