Okuma OSP P100, P200, P300 RS-232 Parameters

Okuma OSP P100, P200, P300 RS-232 Parameters

Controls

  1. OSP-P100L, OSP-P100M
  2. OSP-P200L, OSP-P200M, OSP-P200S, OSP-P200LA, OSP-P200MA, OSP-P200SA
  3. OSP-P300L, OSP-P300M, OSP-P300S, OSP-P300LA, OSP-P300MA, OSP-P300SA
Notate or take a picture of any parameters before you change them

Set Tape Puncher Interface Parameters

  1. Ensure NC PANEL key is set to "UNLOCK"
  2. Press PARAMETER button
  3. Press DISPLAY CHANGE (F8)
  4. Go to OPTIONAL PARA:(TAPE PUNCHER INTERFACE)
  5. Press CLOSE (F8)

Page 1 of 4 - Tape Puncher Interface

To change a parameter, press MENU [*] (F1) or SET (F1)
Press page up and page down buttons to cycle between pages
Set or confirm the following parameters:
  1. Tape code set to "ISO"
  2. ISO/EIA Automatically during reading set to "do not
  3. Tape TV check set to "do not"
  4. Enter tape code in ISO set to "CRLF"
  5. Tape delimiting code set to "%"
  6. Special code set to "ALARM"
  7. Program operation file name punch set to "punch"
  8. Tape feed set to "FEED HOLES"
  9. Tape feed holes set to "1"

Page 2 of 4 - Tape Puncher Interface

  1. Skip this page

Page 3 of 4 - Tape Puncher Interface (Input/Verify Parameter)

Set or confirm the following parameters:
    1. Device name of program operation set to "CN1:"
    2. baud rate(bps) set to "1200", "2400", "4800", "9600", or "19200" (recommended)
    3. RS232C character set to "8 bit"
    4. RS232C parity bit set to "NON"
    5. RS232C stop bit set to "2"
    6. Ready waiting time set to "40"
    7. Flow control set to "DC CODE"
    8. The delay timer until the RS switches OFF set to "0"
    9. Designates the amount of RS OFF time set to "0"
    10. DC3 when read/verify finished set to "DOES"

    Page 4 of 4 - Tape Puncher Interface (Output Parameter)

    Set or confirm the following parameters:
      1. Device name of program operation set to "CN1:"
      2. baud rate(bps) set to "1200", "2400", "4800", "9600", or "19200" (recommended)
      3. RS232C character set to "8 bit"
      4. RS232C parity bit set to "NON"
      5. RS232C stop bit set to "2"
      6. Ready waiting time set to "40"
      7. Flow control set to "DC CODE"
      8. The delay timer until the RS switches OFF set to "0"
      9. Designates the amount of RS OFF time set to "0"
      10. DC2/DC4 at punch set to "DOES NOT"

      Set Optional Read/Write Parameters

      1. Ensure NC PANEL key is set to "UNLOCK"
      2. Press PARAMETER button
      3. Press DISPLAY CHANGE (F8)
      4. Go to OPTIONAL PARA:(READ/WRITE)
      5. Press CLOSE (F8)

      Page 1 of 1 - Read/Write

      Set or confirm the following parameters:
        1. Device number(for parameter set) set to "CN1:"
        2. Tape delimiting code set to "%"
        3. RS232C stop bit set to "2"
        4. RS232C parity bit set to "NON"
        5. Baud rate(bps) set to "1200", "2400", "4800", "9600", or "19200" (recommended)
        6. Flow control set to "DC CODE"
        7. Ready waiting time set to "40"
        8. RS2322C character set to "8 bit"

        Finalize Settings

        1. Reboot control