Legacy
How to Format USB Drive for use with Mazak and Floppy Emulator Connect
Overview Mazaks require a special formatting on floppy disks to function so the same will hold true when using our Floppy Emulator Connect. Formatting the USB Drive Plug in USB drive into the Floppy Emulator Connect Red light on Floppy Emulator ...
Floppy Connect Emulator Installation Guide for Haas Model
Overview The Floppy Connect Emulator emulates your existing floppy drive & acts as if it were never removed. This article is for the Haas model only. USB Flash Drive Requirements We recommend using the included SFA USB flash drive. USB drive must be ...
Floppy Connect Emulator Installation Guide for Universal Model
Overview The Floppy Connect Emulator emulates your existing floppy drive & acts as if it were never removed. Works with almost any existing 720KB/1.44MB capacity DOS format floppy drive. 28 or 32 pin ribbon cables systems are supported & will connect ...
Floppy Connect Emulator Installation Guide for IBM Model
Overview The Floppy Connect Emulator emulates your existing floppy drive & acts as if it were never removed. Works with almost any existing 720KB/1.44MB capacity DOS format floppy drive. 28 or 32 pin ribbon cables systems are supported & will connect ...
LAN Connect Operation Guide
Overview This KB is intended to provide a description of the LAN Connect network FTP data server. The LAN Connect is an FTP server with at least 2 GB of local memory stored on a removable SD card. Data can be accessed over a LAN network as well as ...
LAN Connect Installation Guide
Overview This manual is intended to provide the installation procedure for the LAN Connect pendant-mounted device. Requirements The LAN Connect device will work with a CNC control with a standard DB25 RS-232 serial connection to the control box for ...
What kind of USB flash drives can be used with a floppy drive emulator on my CNC?
You must use a USB flash drive that is 2GB or smaller. The flash drives must be formatted as “FAT” or “FAT-16.” 32-bit FAT (“FAT-32”) will NOT work with the floppy emulator. Review How to Format a USB Flash Drive to FAT to convert any compatible USB ...
Why can I send programs and read/write from the Haas Floppy Emulator, but I can't save programs back to it?
Here are some steps to look into taking for this issue. Does the Haas say FLOPPY DONE when you attempted to save a file to the Floppy Connect? If YES, then do an F4 command on the Haas and select EDIT to view the DIR (Directory) of the floppy ...
How to Format a USB Flash Drive to FAT
Overview Floppy Connect requires a USB flash drive to be formatted as FAT or FAT16. In addition, the Floppy Connect requires a drive to be 2GB or smaller. This knowledge base is written for Windows 10 or newer, however, steps for older operating ...
Floppy Drive Emulator File Size
The Floppy Connect can emulate a 720 KB or 1.44 MB floppy drive. Even with a large USB drive, the maximum file size is 720 KB or 1.44 MB depending on the emulation.
Floppy Connect USB Flash Drive Compatibility
The Floppy Connect must use a USB flash drive of 2 GB or smaller. The USB flash drives must be formatted as FAT or FAT-16. FAT-32 or exFAT will not work with the Floppy Connect. Reach out to your Shop Floor Automations Account Executive to purchase a ...
Unable to Save Programs to Floppy Connect on a Haas
Problem I am unable to save programs back to the Floppy Connect (emulator) on a Haas, but I can load programs from it. Solutions Does the Haas say "FLOPPY DONE" when you attempted to save a file to the Floppy Connect? If yes, then press F4 on the ...
LED Status Lights on the Floppy Connect Emulator
Green LED Status Light The green light indicates a floppy read or write operation has been done. No green light at all, or solid green light, indicates a problem. Red LED Status Light The red light indicates that the USB drive is inserted. The red ...